Class 11 Geography Chapter 25 Topographical Maps Short Notes in English

A last-minute revision squeeze of this chapter: the definition of a topographical map, India’s two map series and five scales, the methods of relief representation, contour interval versus horizontal equivalent, the contour identification of slopes and landforms, the eight steps of a cross-section, settlements, and map interpretation, all in one place. The full detailed notes are available separately for a complete read.

1 Two definitions to learn by heart

Learn by heartDefinition 1

Topographical Map is a map that shows the natural and man-made features of the earth’s surface on a large scale, with relief shown through contours; it serves as the base map for all other maps.

Learn by heartDefinition 2

Contour is an imaginary line joining points of equal elevation above mean sea level; a map that shows landform through such lines is called a contour map.

Exam Tip

The difference between contour interval (V.I.) and horizontal equivalent (H.E.), and the latitude-longitude coverage of the Survey of India’s five scales, are the two most direct, fact-based questions from this chapter.

2 India’s two map series and five scales

Scale Latitude × Longitude coverage
1 : 10,00,000 4° × 4°
1 : 2,50,000 1° × 1°
1 : 1,25,000 30′ × 30′
1 : 50,000 15′ × 15′
1 : 25,000 5′ × 7′30″

Two series: the India and Adjacent Countries Series (until the Delhi Survey Conference of 1937; afterward, India’s own maps kept the old numbering system but followed the new International Map Series’ specifications) and the International Map Series of the World (1 : 10,00,000 or 1 : 2,50,000).

Sheet numbering (book Figure 5.1): a 4° × 4° sheet (e.g. 63) is divided into 16 sheets of 1° × 1° lettered A to P (e.g. 63K), each divided into 16 sheets of 15′ × 15′ numbered 1 to 16 (e.g. 63K/12); letters and numbers run down each column from the north-west corner.

3 Five methods of relief representation

All five methods, in one line
  • Hachures: short straight lines drawn along the direction of maximum slope
  • Hill shading
  • Layer tints: height shown through bands of colour
  • Bench marks and spot heights: marking the surveyed height of fixed points
  • Contours: lines joining places of equal height

Of these, contours and spot heights are the two used predominantly on all topographical maps.

4 Contour interval (V.I.) versus horizontal equivalent (H.E.)

Term Meaning Behaviour
Contour Interval (V.I.) The vertical gap between two successive contours Usually constant on a given map, expressed in metres
Horizontal Equivalent (H.E.) The horizontal distance between the same two contours Changes with slope: large on a gentle slope, small on a steep slope
Common Mistake

Do not assume that both the V.I. and the H.E. stay constant. The V.I. stays constant, but the H.E. keeps changing with the steepness of the slope: this is exactly why, even on a map with a single fixed contour interval, the contours appear close together over a hill and far apart over a plain.

5 Five basic features of contour lines

  1. They show places of equal height.
  2. Their shape and spacing show the height and slope of the land.
  3. Closely spaced = steep slope; widely spaced = gentle slope.
  4. Two or more contours merging = a near-vertical feature (a cliff or a waterfall).
  5. Two contours of different elevation usually do not cross each other.

6 Types of slope

The book names five: gentle, steep, concave, convex and irregular or undulating. It illustrates the first four:

Slope Contour identification
Gentle Slope Low angle, contours far apart
Steep Slope High angle, contours close together
Concave Slope Gentle below (far apart), steep above (close together)
Convex Slope Gentle above (far apart), steep below (close together)

Memory trick: concave curves in like the inside of a cave, steep near the top; convex bulges out like the outside of a dome, steep right at the bottom.

7 Contour identification of landforms

Landform Contour identification
Conical Hill Concentric contours at roughly regular intervals
Plateau Close together at the margin, wide gap inside
‘V’-Shaped Valley (mountainous, river erosion) Very small gap in the innermost contour
‘U’-Shaped Valley (glacial erosion) Wide gap in the innermost contour
Gorge Very closely spaced contours, small gap in the innermost contour
Spur V-shaped contours reversed: arms toward higher ground
Cliff Very closely spaced, eventually merging contours
Waterfall / Rapids Contours crossing the river merge / relatively distant contours

8 Eight steps of a cross-section

  1. Draw a straight line across the contours and label it AB.
  2. Take a strip of plain or graph paper and lay its edge along AB.
  3. Mark the position and value of every contour that AB crosses.
  4. Choose a suitable vertical scale; draw parallel horizontal lines as long as AB.
  5. Mark the contour values up the vertical axis of the cross-section, starting from the lowest value.
  6. Lay the marked paper’s edge along the base line; transfer the contour points.
  7. Draw a perpendicular from AB at every contour point.
  8. Join all the points with a smooth line to complete the profile.

9 Settlements and map interpretation

Category Types / factors
Rural settlement (4 types) Compact, scattered, linear, circular
Urban centre (9 types) Cross-road, nodal, market, hill station, coastal resort, port, manufacturing, capital, religious
Settlement-site factors (5) Source of water, food supply, relief, occupation, defence
Interpretation heads (5) Marginal information, relief and drainage, land use, transport and communication, human settlement

Settlement density is directly related to the food supply. Interpretation procedure: find the location from the sheet number → trace the features onto tracing paper → describe the distribution pattern → superimpose pairs of maps to find the relationship.

Quick Revision: read this the night before the exam
  • Topographical map = base map, prepared by the Survey of India, at five scales
  • V.I. is constant, H.E. changes with slope (large on a gentle slope, small on a steep slope)
  • 5 basic features of contours; 5 types of slope (4 illustrated); 6-7 contour identifications of landforms (including the V/U valley and the spur)
  • Remember the 8 steps of a cross-section (line AB → scale → mark → join)
  • 4 types of rural settlement, 9 types of urban centre, 5 settlement-site factors, 5 interpretation heads
Check yourself before the exam

Can I state the latitude-longitude coverage of all five Survey of India scales? Can I tell a ‘V’-shaped valley, a ‘U’-shaped valley and a spur apart from their contours? Do I remember all eight steps of drawing a cross-section, in order?