All the questions NCERT Exploration, Class 9 Science, Chapter 7, “Work, Energy, and Simple Machines”, asks inside the chapter (Think It Over, all thirteen Pause and Ponder questions, Activities 7.1 to 7.5 and the What If box), then all fifteen questions from the “Revise, Reflect, Refine” exercise exactly as printed in the book, and finally The Journey Beyond, with a full model answer under each. Write your own answer first, then compare.
1 Think It Over
Q. (a) What will be the magnitude of velocity of the child at the bottom of the blue slide? (b) Will two children of different masses reach the bottom of the same slide with the same velocity? (c) Which of the slides will result in the largest magnitude of velocity for the child at its bottom?
Answer: (a) Neglecting friction, the child’s potential energy at the top, mgh, becomes kinetic energy ½mv2 at the bottom, so v = √(2gh), where h is the height of the top of the blue slide above its bottom (Example 7.8).
(b) Yes. In v = √(2gh) the mass cancels out, so children of different masses reach the bottom of the same slide with the same speed (ignoring friction).
(c) The speed at the bottom depends only on the height through which the child comes down, not on the shape or length of the slide. So, ignoring friction, the slide whose top is at the greatest height above its bottom gives the largest speed (Example 7.8). Slides whose tops are at the same height give the same speed, whatever their shape. To answer for the picture, compare the heights of the tops of the slides above their bottoms.
2 Pause and Ponder 1 and 2: Is any work done?
Q. In the previous chapter, a weightlifter is shown holding a barbell steady in her hands (Fig. 6.8). Is she doing any work on the barbell while holding it steady?
Answer: No. She applies an upward force equal to the barbell’s weight, but the barbell does not move, so its displacement is zero and the work done on it (W = F × s) is zero. She still feels tired because her muscles use up the internal energy of her body.
Q. Is the work done by friction on the stack of coins that travels on a rough surface (Fig. 6.13c) positive, negative or zero?
Answer: Negative. The force of friction acts opposite to the direction in which the coins move, so the force and the displacement are in opposite directions. This negative work reduces the kinetic energy of the coins until they stop.
3 Pause and Ponder 3: Energy while cycling
Q. When you pedal a bicycle on a flat road, your muscles supply energy. In what forms does this muscular energy appear as you ride?
Answer: The muscular energy comes from the chemical energy of food. While you speed up, part of it becomes the kinetic energy of you and the bicycle. On a steady ride on a flat road your kinetic energy stays the same, so the energy you keep supplying goes mostly into thermal energy (heat): in your body, and through friction in the chain, the tyres and the road, and against air resistance. A little appears as sound.
4 Pause and Ponder 4 and 5: Kinetic energy
Q. Two objects A and B of mass m and 4m have the same kinetic energy. What is the ratio of the magnitude of velocities of A and B?
Answer: ½ m vA2 = ½ (4m) vB2, so vA2 = 4 vB2 and vA = 2 vB. The ratio vA : vB = 2 : 1.
Q. Does the kinetic energy of an object which moves with constant velocity change with its position?
Answer: No. Kinetic energy K = ½mv2 depends only on the mass and the speed of the object. With a constant velocity the speed does not change, so the kinetic energy stays the same wherever the object is.
5 Activity 7.1: A ball dropped on sand
Q. A heavy ball is dropped on a bed of loose sand from a height of about 1 m, and then from 2 m at another spot. Is a depression created in the sand? Why does the ball create a depression? Compare the depths of the depressions: in which case is the depression deepest and in which case the shallowest?
Answer: Yes, a depression is created. The falling ball has energy (its potential energy at the height changes into kinetic energy as it falls), and on hitting the sand it does work in pushing the sand aside. The depression is deepest when the ball is dropped from the greatest height (2 m) and shallowest from the smallest height (1 m). Raising the ball higher needs more work, so it has more potential energy: the greater the height, the greater the potential energy.
6 Pause and Ponder 6: Potential energy and height
Q. Does the potential energy of an object near the surface of the Earth change if it moves with constant velocity in the horizontal direction? What if the object is gradually raised in the vertical direction?
Answer: Moving horizontally, its height above the ground does not change, so its potential energy U = mgh does not change. When it is raised vertically, h increases, so its potential energy increases (by mg for every metre it is raised).
7 Activity 7.2: The swinging pendulum
Q. The bob of a simple pendulum is taken to a point P at the level of a horizontal line drawn above its rest position and released. Observe it at the extreme points of the first couple of oscillations. Does the bob almost reach the level of the horizontal line?
Answer: Yes, on the other side (point R) the bob rises almost to the same horizontal line. At P it has only potential energy (mgh); at the lowest point Q this has become kinetic energy; at R the kinetic energy is zero and the potential energy is back to nearly mgh. The mechanical energy of the bob remains nearly constant. Over many oscillations the bob rises a little less each time and finally stops, because of energy lost to friction at the support and air resistance.
8 Pause and Ponder 7 and 8: Conservation of mechanical energy
Q. For the situation depicted in Fig. 7.19, calculate the mechanical energy of the ball just before it hits the ground and show that even at this position, it is mgh.
Answer: Just before the ball hits the ground its height is zero, so its potential energy is mg × 0 = 0. It has fallen through the height h from rest, so v2 = u2 + 2gh = 2gh. Its kinetic energy is ½mv2 = ½m(2gh) = mgh.
Mechanical energy = potential energy + kinetic energy = 0 + mgh = mgh, the same as at the starting point A.
Q. You may have seen an exhibit like that in Fig. 7.22 in a science park, where a ball is released from the highest point. Describe how the kinetic energy and potential energy change at points A, B and C. Why do subsequent points, such as C, D and E, usually have lower heights compared to the previous ones? Could it have anything to do with the energy lost due to friction?
Answer: As the ball runs down from the highest point, its potential energy changes into kinetic energy. At the hump A the ball is high again, so it has a large potential energy and a smaller kinetic energy. Going down into the dip B, its potential energy is the least and its kinetic energy the greatest. Climbing to the next hump C, kinetic energy changes back into potential energy, so it slows down again.
Each later hump is usually lower than the one before because the ball loses some energy at every stage to friction with the track and to air resistance (as heat and sound), so it does not have enough mechanical energy left to climb back to an earlier height. So yes, energy lost to friction (and air resistance) is why C, D and E are usually lower than the points before them.
9 Activity 7.3: Pulling a cart up an inclined plank
Q. A cart is first lifted vertically to the top of a stool or a pile of books with a spring balance, and then pulled up a plank resting against it. Is the reading of the spring balance (the force required) smaller than when the cart was lifted vertically? Reduce the angle of the plank and repeat: how does the force required change as the plank becomes less steep?
Answer: Yes, the reading while pulling the cart up the plank is smaller than the reading when lifting it straight up (which equals the cart’s weight). When the plank is made less steep, the reading becomes even smaller. But the cart now has to be pulled over a larger distance to reach the same height, so the work done (force × distance) stays the same. The inclined plane makes the task easier by reducing the force, not the work.
10 Pause and Ponder 9 and 10: Inclined planes around us
Q. Explain why roads on hills are built to wind around in gentle slopes rather than going straight up (Fig. 4.26)?
Answer: A winding road with a gentle slope is a long inclined plane. Its mechanical advantage, L/h, is large because the road length L is much greater than the height h gained. So a vehicle needs a much smaller force to climb it than a steep road going straight up would need, even though the work done to reach the top is the same.
Q. To reach a higher floor, we find climbing an inclined ladder easier in comparison to climbing a vertical ladder (Fig. 7.30). Explain why.
Answer: An inclined ladder works like an inclined plane. To reach the same height we move along a longer path, so at each step we have to lift our body through a smaller height and the force needed is smaller; part of our weight is also supported by the sloping ladder. On a vertical ladder we have to pull our whole weight straight up. The total work done (mgh) is the same in both cases, but the inclined ladder needs less effort.
11 Activity 7.4: Lifting a stapler with erasers
Q. A 30 cm scale is placed over a pencil, with the pencil close to one end. A stapler is placed on the end near the pencil and an eraser on the other end. Does the stapler lift up? If not, add one more eraser.
Answer: With one eraser the stapler may not lift. When one more eraser is added, as the book suggests, the stapler can be lifted, although it is much heavier than the erasers. The scale acts as a lever that turns about the pencil (the fulcrum). The erasers are far from the fulcrum (long effort arm) and the stapler is close to it (short load arm), so a small effort balances a much larger load.
12 Activity 7.5: A beam balance with coins (Table 7.1)
Q. A scale hung at its midpoint carries a paper cup at each end. With 1 coin in the left pan (effort) and 2, 4 and then 8 coins in the right pan (load), the right pan is moved towards the centre until the beam balances, and its distance from the fulcrum is measured. Complete Table 7.1. What do you conclude?
Answer: With the left pan kept, for example, at L1 = 20 cm from the fulcrum, the beam balances when the right pan is at:
1 coin and 1 coin: L2 = 20 cm
1 coin and 2 coins: L2 = 10 cm
1 coin and 4 coins: L2 = 5 cm
1 coin and 8 coins: L2 = 2.5 cm
Each time the load is doubled, its distance from the fulcrum has to be halved. So the beam balances when n1 × L1 = n2 × L2, that is, effort × effort arm = load × load arm. (Your own readings will be close to these values.)
13 Pause and Ponder 11 to 13: Levers and machines
Q. Why is it easier to open the lid of a can by using a spoon as shown in Fig. 7.35?
Answer: The spoon acts as a lever. The rim of the can is the fulcrum, the lid just next to it is the load, and the effort is applied at the far end of the handle. The effort arm is much longer than the load arm, so (effort × effort arm = load × load arm) a small effort on the handle produces a large force on the lid and opens it easily.
Q. Why do you push an object closer to scissors fulcrum when you want to cut an object which is hard?
Answer: Scissors are a lever with the fulcrum at the pivot. Pushing the hard object closer to the fulcrum makes the load arm shorter while the effort arm (from the fulcrum to your fingers) stays the same. Since effort × effort arm = load × load arm, a shorter load arm means the same effort applies a larger force on the object, which is needed to cut it.
Q. Throughout history, many designs of perpetual machines (using wheels, weights or magnets) have been proposed but none actually work. Why do all real machines eventually slow down and stop? Explain in terms of work and energy.
Answer: A machine cannot create energy; it only passes on the energy given to it. In every real machine some of this energy is always lost, mostly as heat, through friction at the moving parts and air resistance. Work done against friction is not stored. So unless energy is supplied from outside (fuel, electricity, muscle), the machine’s mechanical energy keeps decreasing, and it slows down and finally stops.
14 What if a perpetual motion machine were possible?
Q. What if it were possible to build a perpetual motion machine, which once started, could continue doing useful work forever, without any fuel or electricity?
Answer: Such a machine would be giving out energy (useful work) forever without taking in any, that is, it would be creating energy out of nothing. That goes against the principle that energy can only change from one form to another and that machines do not create energy. If it were possible, the world would have an endless free source of energy, with no need for fuel, electricity or dams. In reality friction always takes away some energy, which is why no such machine has ever worked.
15 True or False
Q. State whether True or False.
(i) Work is said to be done when a force is applied, even if the object does not move.
(ii) Lifting a bucket vertically upward results in positive work done on the bucket.
(iii) The SI unit for both work and energy is joule (J).
(iv) A motionless stretched rubber band has kinetic energy.
(v) Energy can change from one form to another.
Answer:
(i) False. Work needs both a force and a displacement of the object in the force’s direction; a force with no displacement does zero work.
(ii) True. The lifting force and the upward displacement point the same way, so the work done is positive.
(iii) True. Both work and energy are measured in joules.
(iv) False. A motionless stretched rubber band has zero kinetic energy, since it is not moving; the stored energy is potential energy, not kinetic.
(v) True. Energy readily converts between mechanical, thermal, chemical, electrical and other forms.
16 Fill in the Blanks
Q. Fill in the blanks.
(i) Work done = ______ × ______ (in the direction of force).
(ii) 1 joule of work is done when a force of ______ newton displaces an object by 1 metre in the direction of the force.
(iii) The expression for kinetic energy of a body of mass m and velocity v is ______.
(iv) The potential energy of an object of mass m at a small height h from the Earth’s surface is ______.
(v) Power is defined as the ______ at which work is done.
Answer:
(i) force × displacement
(ii) 1 newton
(iii) K = ½mv²
(iv) U = mgh
(v) rate
17 Ball at Its Highest Point
Q. When a ball thrown upwards reaches its highest point, tick which of the following statement(s) are correct?
(i) The force acting on the ball is zero.
(ii) The acceleration of the ball is zero.
(iii) Its kinetic energy is zero.
(iv) Its potential energy is maximum.
Answer: Only (iii) and (iv) are correct. At the highest point the ball is momentarily at rest, so its speed and hence its kinetic energy are zero, while its height, and so its potential energy, is at a maximum. Statements (i) and (ii) are wrong: gravity keeps acting on the ball throughout its flight, so both the force (mg) and the acceleration (g, downward) stay exactly the same at the top as everywhere else.
18 Identifying Energy Transformations
Q. For each of the following situations, identify the energy transformation that takes place: (i) a truck moving uphill, (ii) unwinding of a watch spring, (iii) photosynthesis in green leaves, (iv) water flowing from a dam, (v) burning of a matchstick, (vi) explosion of a fire cracker, (vii) speaking into a microphone, (viii) a glowing electric bulb, and (ix) a solar panel.
Answer:
(i) Chemical energy (fuel) → kinetic and potential energy of the truck.
(ii) Potential (elastic) energy of the wound spring → kinetic energy of the watch’s moving parts.
(iii) Light energy → chemical energy stored in the leaf.
(iv) Potential energy of the stored water → kinetic energy of the falling water.
(v) Chemical energy → heat and light energy.
(vi) Chemical energy → heat, light and sound energy (and kinetic energy of the fragments).
(vii) Sound energy → electrical energy.
(viii) Electrical energy → light and heat energy.
(ix) Light (solar) energy → electrical energy.
19 Elevator vs Stairs
Q. A student is slowly lifted straight up in an elevator from the ground level to the top floor of a building. Later, the same student climbs the staircase, all the way to the top. Given that the height of the building is h = 72.5 m, acceleration due to gravity is g = 10 m s⁻², and student’s mass is m = 50 kg.
(i) Find the gain in the potential energy if the student is lifted straight up to the top.
(ii) Find the gain in the potential energy when the student climbs the stairs to the same top.
(iii) What do you conclude about the dependence of the potential energy on the path taken?
Answer:
(i) Gain in PE, using the elevator: U = mgh = 50 × 10 × 72.5 = 36,250 J.
(ii) Gain in PE, using the stairs: the mass, g and the final height above the ground are exactly the same, so U = mgh = 50 × 10 × 72.5 = 36,250 J again.
(iii) The gain in potential energy is exactly the same by both routes. This shows that gravitational potential energy depends only on the object’s initial and final height, not on the path taken to get there.
20 Crane to the 10th and 20th Floor
Q. A crane lifts a mass m to the 10th floor of a building in a certain time. It then raises the same mass to the 20th floor of the same building in double the time. How much more energy and power are required? Assume that the height of all floors is equal.
Answer: Let each floor have height h₀ and let the crane take time t to reach the 10th floor.
Energy for the 10th floor: E₁ = mg(10h₀). Energy for the 20th floor: E₂ = mg(20h₀) = 2E₁, since the crane must lift the same mass through twice the height.
Extra energy required = E₂ − E₁ = mg(20h₀) − mg(10h₀) = mg(10h₀) = E₁, that is, as much more energy as was needed to reach the 10th floor; the 20th floor needs twice the total energy.
Power for the 10th floor: P₁ = E₁/t. Power for the 20th floor: P₂ = E₂/(2t) = 2E₁/2t = E₁/t = P₁.
So even though the crane does twice the work, it also takes twice the time, and the power required is exactly the same in both cases.
21 Raising a Flag with a Pulley
Q. Which factors determine the energy required to raise a flag from the ground to the top of a tall flagpole using a pulley? Does raising the flag slowly or quickly change the amount of work done? If the speed at which the flag is raised is doubled, how does the power requirement change? Explain your answers.
Answer: The energy required is E = mgh, so it depends only on the flag’s weight (mg) and the height of the flagpole (h); it does not depend on how fast the flag is raised.
Raising the flag slowly or quickly therefore does not change the total work done, since work = mgh either way.
Power, however, is work divided by time, so it very much depends on speed. If the flag is raised at double the speed, it reaches the top in half the time, so the power required, P = W/t, doubles.
22 Scooter With and Without a Passenger
Q. A man of mass 60 kg rides a scooter of mass 100 kg. He accelerates the scooter to a velocity v. The next day, his son with a mass of 40 kg joins him as a passenger. If the scooter reaches the same speed on both days in the same time interval, what is the ratio of the fuel of the tank used on the two days? Assume that the energy transfer to the scooter happens entirely due to fuel, and no other losses occur due to air resistance and friction.
Answer: Day 1 total mass = 60 + 100 = 160 kg. Day 2 total mass = 60 + 100 + 40 = 200 kg. Both reach the same final speed v from rest, so the fuel energy used equals the kinetic energy gained in each case:
KE₁ = ½(160)v², KE₂ = ½(200)v².
Ratio of fuel used, day 1 to day 2 = KE₁ : KE₂ = 160 : 200 = 4 : 5.
23 A Seesaw with an Adult and a Child
Q. On a seesaw with sliding seats, a child is sitting on one side and an adult on the other side. The adult weighs twice that of the child. The seesaw however is balanced. Draw a figure which depicts this situation showing the distances from the fulcrum where the child and the adult are seated.
Answer: Let the child have weight W and sit at a distance d₁ from the fulcrum, and let the adult, of weight 2W, sit at a distance d₂ from the fulcrum on the other side. Balancing the seesaw (a Class I lever) requires the two turning effects to be equal: W × d₁ = 2W × d₂, so d₁ = 2d₂.
Figure description: a horizontal plank rests on a central triangular fulcrum. On the left, the child (weight W) sits at distance d₁ from the fulcrum. On the right, the adult (weight 2W) sits at distance d₂ = d₁/2 from the fulcrum, that is, at exactly half the child’s distance, since the adult weighs twice as much. For example, if the child sits 2 m from the fulcrum, the adult must sit 1 m from it for the seesaw to balance.
24 A Ball Thrown Upward, with Air Resistance
Q. A ball of mass 2 kg is thrown up with a velocity of 20 m s⁻¹.
(i) Identify the sign of the work done by gravity on the ball during its upward motion and its downward motion.
(ii) If the ball reaches a height of 19.4 m, how much work was done by air resistance (assume g = 10 m s⁻²).
Answer:
(i) During the upward motion, the ball’s displacement is upward while gravity acts downward, so gravity and displacement are opposite, and the work done by gravity is negative. During the downward motion, both the displacement and gravity point downward, so the work done by gravity is positive.
(ii) Initial kinetic energy = ½(2)(20)² = 400 J. At the highest point the ball is momentarily at rest, so its final kinetic energy is 0, giving ΔKE = 0 − 400 = −400 J.
Work done by gravity over the actual height reached, 19.4 m: Wg = −mgh = −(2)(10)(19.4) = −388 J.
By the work-energy theorem, the total work done by all forces equals ΔKE: Wg + Wair = ΔKE, so Wair = −400 − (−388) = −12 J. The negative sign confirms air resistance, as expected, removes energy from the ball rather than adding to it.
25 A Block Under a Variable Force
Q. A 10.0 kg block is moving on horizontal floor with negligible friction. As shown in Fig. 7.37, a variable force is applied on the block in its direction of motion from its position at 0 m till 4 m. If the block had a kinetic energy of 180 J when it was at 0 m, find the block’s speed (i) at 0 m, and (ii) at 4 m. Does the block have negative acceleration in any portion of its motion?
Answer: The force-displacement graph rises in a straight line from 0 N at 0 m to 50 N at 1 m, stays constant at 50 N from 1 m to 3 m, then falls in a straight line from 50 N at 3 m back to 0 N at 4 m.
Speed at 0 m: from KE = ½mv², 180 = ½(10)v₀², so v₀² = 36, giving v₀ = 6 m/s.
Work done from 0 m to 4 m = area under the force-displacement graph = (triangle, 0 to 1 m) + (rectangle, 1 to 3 m) + (triangle, 3 to 4 m) = ½(1)(50) + (2)(50) + ½(1)(50) = 25 + 100 + 25 = 150 J.
Speed at 4 m: KE at 4 m = 180 + 150 = 330 J, so 330 = ½(10)v₄², v₄² = 66, giving v₄ = √66 ≈ 8.12 m/s.
Negative acceleration: No. The applied force (and hence the acceleration, since F = ma) is zero or positive throughout, from 0 up to 50 N and back down to 0, but it never becomes negative or opposes the motion, so the block keeps speeding up the whole way, just more slowly after 3 m as the force tapers off.
26 Throwing a Ball on the Moon
Q. The gravitational attraction on the surface of the Moon (lunar surface) is about ⅙th of that on the surface of the Earth. An astronaut can throw a ball up to a height of 8 m from the surface of the Earth. How far up will the ball thrown with the same upward velocity travel from the surface of the Moon?
Answer: Let the launch speed be u, and let Earth’s gravity be g. Using v² = u² − 2gh with v = 0 at the top: u² = 2gh, so on Earth, u² = 2g(8) = 16g.
On the Moon, gravity is g/6, so the height reached, h_moon = u²/(2 × g/6) = 16g × 6/(2g) = 96/2 = 48 m.
Since height for a given launch speed is inversely proportional to g, reducing gravity to one-sixth lets the ball rise exactly six times as high: 8 m × 6 = 48 m.
27 A Car Braking to a Stop
Q. A 1000 kg car is moving along a road at a constant speed. Suddenly, the driver notices some obstruction ahead and applies the brakes to come to a complete stop. The graphical representation of motion of the car starting from the instant the driver spots the traffic ahead is shown in Fig. 7.38.
(i) Describe how the car moves between positions A and B.
(ii) Calculate the kinetic energy of the car at A.
(iii) State the work done by the brakes in bringing the car to a halt between B and C.
(iv) What does the kinetic energy of the car transform into?
Answer: The graph shows the car at a constant speed of 35 m/s from A (t = 0 s) to B (t = 1 s), then slowing uniformly from 35 m/s at B to 0 m/s at C (t = 3 s).
(i) Between A and B the car moves at a constant speed of 35 m/s; the brakes are not yet acting, so there is no change in speed. (The book does not name this interval; it fits the time the driver takes to react after spotting the obstruction.)
(ii) KE at A = ½(1000)(35)² = ½(1000)(1225) = 612,500 J (6.125 × 10⁵ J).
(iii) Since the speed at B is the same as at A (35 m/s) and the car comes to rest at C, the work done by the brakes equals the change in kinetic energy from B to C: W = 0 − 612,500 = −612,500 J, negative because the braking force opposes the car’s motion.
(iv) The kinetic energy transforms mainly into heat at the brake pads, discs and tyres, with a small amount as sound.
28 A Ball on a Frictionless Track
Q. The potential energy-displacement graph of a 0.5 kg ball moving along a frictionless track is shown in Fig. 7.39. At O, the velocity of the ball is 0 m s⁻¹ and potential energy is 30 J. Calculate the velocity of the ball at P, Q and R.
Answer: Since the ball starts at rest at O with PE = 30 J, its total mechanical energy is ME = KE + PE = 0 + 30 = 30 J, and this stays constant everywhere on the frictionless track.
At P (PE = 20 J): KE = 30 − 20 = 10 J, so ½(0.5)v² = 10, v² = 40, giving v_P = √40 ≈ 6.32 m/s.
At Q (PE = 30 J, the same as at O): KE = 30 − 30 = 0, so v_Q = 0 m/s. Q is a second turning point, exactly as high as O.
At R (PE = 40 J, read off the graph): this is higher than the ball’s total mechanical energy of 30 J, which would require a negative kinetic energy, an impossibility. This means the ball, released from O with only 30 J to spend, can never actually reach R; it must turn back at Q, where its speed first returns to zero, before it ever gets that far along the track.
29 A Coconut Falling onto Sand
Q. A coconut of mass 1.5 kg falls from the top of a coconut tree onto the wet sand on a beach. The height of the tree is 10 m. On impact, the coconut comes to rest by making a depression in the sand.
(i) Calculate the velocity of the coconut just before it hits the sand.
(ii) Assume that the average resistive force of sand is 3000 N and all of the coconut’s energy is used to create the depression in the sand. Calculate the depth of the depression the coconut makes in the sand. Assume g = 10 m s⁻².
Answer:
(i) Using v² = 2gh = 2(10)(10) = 200, v = √200 ≈ 14.14 m/s.
(ii) Energy of the coconut just before impact = mgh = 1.5 × 10 × 10 = 150 J. Since this entire energy is used to create the depression against the resistive force F, F × d = 150, so d = 150/3000 = 0.05 m = 5 cm.
30 The Journey Beyond
Q. A pen refill attached to a stretched rubber band shoots out of the barrel when the band is released. Repeat with different amounts of stretch, and observe how the distance travelled changes. Is there a relationship between the stretch and the distance travelled?
Answer: Yes. The more the rubber band is stretched, the more work is done on it and the more elastic potential energy it stores. On release this energy becomes the kinetic energy of the refill, so a larger stretch should make the refill shoot out faster and travel a larger distance. Record the stretch and the distance for each try to check this relationship with your own readings.
Q. Construct one or more simple machines, or a combination of them (lever, pulley, and inclined plane) using easily available materials, such as cardboard, wooden strips or rulers, pencils or bolts (to act as a fulcrum), thread or rope, small pulleys (or two bottle caps stuck together), and paper cups to hold small weights. Be imaginative in your design. Use your model to lift or move a small load, measure the effort and the load, and calculate the mechanical advantage.
Answer: This is an open-ended project. For example, a ruler resting on a pencil is a lever, a thread over two bottle caps stuck together is a pulley, and a sloping piece of cardboard is an inclined plane. Measure the load (the weight lifted, for example with a spring balance) and the effort you apply, then use mechanical advantage = load ÷ effort. For a lever this should come out close to effort arm ÷ load arm, and for an inclined plane close to L ÷ h; friction in a real model makes it a little smaller.
Q. Computer simulations can help in visualising physical quantities that are difficult to observe directly. The PhET simulations (https://phet.colorado.edu) provide interactive models, such as Energy Skate Park, Energy Forms and Changes, Pendulum Lab, and Masses and Springs. Use these to explore how different forms of energy change as parameters, such as mass, height, and friction are varied.
Answer: This is an open-ended exploration. With friction set to zero, the total of kinetic and potential energy stays the same as the skater or pendulum moves, and the speed at the bottom depends on the starting height, not on the mass. With friction turned on, part of the mechanical energy changes into thermal energy, so the skater or the bob no longer returns to its starting height.